Solarwize Lithium Ion Battery - 24V 2.9kWh 120Ah

Solarwize BL10012 - 24V 100Ah 2.9kwh - Lithium Battery

These batteries are ideal for trailers or caravan and can be used for small home standby and solar applications.

Product Specification - Datasheet

Model No: BL12024

Rated Voltage: 24V

Capacity: 120Ah/2900Wh/2.9KWh

Bulk Charge Voltage: 28.9V

Floating Charge Voltage: 28.4V

Cut-Off Voltage: 24V

Max Continuous Charge Current: 110A

Max Continuous Discharge Current: 110A

C-Rating: 1.0C

Weight: 27.0kg

Temperature: -10°C~55°C

Display: LCD Shows Capacity, Faults Recorded, Cycle Life, Current Rating

Additional Display: 5xLED Capacity, Alarm LED, Run LED

Dimensions: 340 x 150 x 375mm

Parallel: Up to 15 units with Communication

Ports: 1X CAN-BUS 2X RS-485 1XRS232

DC Ports: CONNECTOR BLOCK 150A 2XRED 2XBLACK

Cells: First Life BYD 3.7V Li-ion Cells

Design Life: 15 Years

Warranty: 7 Years/6000 Cycle @ 80% DOD

BMS: SMART BMS MEASURE INDIVIDUAL CELL VOLTAGE, CURRENT AND TEMPERATURE. CAN
ACCESS WITH PC

Certifications: CE, UN3840 , GBT31485-2015

Shell Materieal: BLACK/SILVER CORROSION RESISTANT STEEL CASE

Nett Weight:  26.8kg

Gross Weight: 27 kg

Cell Brand: BYD

Output Voltage: 24V

Rated Capacity: 2900Wh

Protection: OVER AND UNDER VOLTAGE , OVER AND UNDER CURRENT, OVER TEMPERTURE
PROTECTION

Dip Switch Settings
After the battery system is installed, you need to connect the RS485/RJ45 network cable port of
the BMS module with a communication network cable. Multiple BMS modules can be connected in
cascade with a communication network cable (no connection is required when a single module is
used).
Multiple: When BMS modules are used in parallel, it is necessary to set the communication address
(that is, the dial switch ADD). When a single BMS module is used, the communication address is1, and
the dial is "1". The original state is "0", which means "OFF", dial up to "1",which means "ON".
Note: Both RS485 network cable ports of BMS can communicate. Multi-level cascade starts from
address #1 (communication starts from 112) and dials according to the dial switch comparison table
as shown below. Through the host computer software, set the master-slave BMS, usually the first
one is the master BMS, and the others are set as the slave BMS, up to12 units in parallel.

Safety Precautions
The battery module must be used in conjunction with BMS, and the mixed use of batteries from
different manufacturers is strictly prohibited .
Check the battery module voltage for damage; if there is any abnormality, please stop using it.
It is strictly forbidden to stack the whole trailer battery with fork plated u ring transportation and
storage, and it is forbidden to stack battery modules when installing and transporting batteries.
There are positive and negative lead terminals or sampling line lead ends, and it is strictly forbidden to
squeeze, stack and place them down.
For parallel matching requirements for battery modules; (Notes before picking and installation), two
identical models and same capacity, The battery modules of the same voltage a reconnected in
parallel to 24V. Serial use is strictly prohibited.
Parallel wires are included in the battery module packing box, and the parallel wires correspond to
the battery modules. Mixed insertion is strictly prohibited.
It is forbidden to use or leave the battery module near high temperature and high heat sources, away
from fire and water sources.
It is forbidden to disassemble the battery module, knock, throw or step on the battery module, and
dismantle the BMS and dismantle the yellow tamper-evident sticker without authorization.
Before installing the battery module, check whether the open circuit voltage of the battery is within
the normal range. The "positive" and "negative" signs are printed on the module, and the electrical
properties should be correctly determined. lt is strictly forbidden to reverse or short-circuit the
battery.
Insulation tools and gloves should be used during installation and transportation , and metal-
containing conductors such as watches, bracelets (bracelets) and rings should be removed from the
wrist to prevent electric shock and short-circuit the positive and negative electrodes. During
installation, the battery module poles need to be insulated and protected. If the poles are close to the
battery rack and other conductors, the battery poles or battery racks need to be insulated and
protected.
The recommended transportation method is for two people to carry it at the same time. The
transportation tool is a safety rope or a load-bearing net bag. The battery box must be carried to the
site. Violent construction is strictly prohibited to damage the product.
Installation and maintenance requirements. After the battery module is installed on the wall, the
poles and plug-ins are required to achieve frontal maintenance.
Battery rack compatibility; multiple groups of parallel type batteries, battery rack installation steps,
battery module installation and cable connection, according to the different types of batteries to
choose the corresponding installation diagram, installation without battery rack (such as outdoor
integration Power cabinet) Refer to the schematic diagram of battery module installation and cable
connection in battery rack mode.
Please read this installation manual carefully before installation. If you have any questions, please
contact your supplier.